Trimaran Education

Colligo Marine lashing tie off instructions

At 180 Marine we only use Dyneema. This is a great illustration from Colligo Marine on lashing the side stays.

Is Dyneema stronger than Kevlar?
You've probably heard about these fibers' strength-to-weight ratio before. Kevlar® states it is 5 times stronger than steel on an equal-weight basis and Dyneema® boasts an impressive 15 times stronger. ... Kevlar® has a tensile strength of 3620 MPa and Dyneema® has 3600 MPa of tensile strength.

This image shows a nicely finished off lashing using our CSS71 Line Terminator and CSS61 Chainplate Distributor using 5 mm or 3/16” Dyneema line.

You can see the critical hourglass shape that gets tighter as the shroud tension gets tighter. It is very secure but is also allows for easy unlashing. Without the hourglass shape you would need to place the knot at the bottom of the lashing which makes it very painful to lash and unlash.

There is a series of individual half hitches that form the attractive spiral configuration of the lashing. This also creates redundant security ensuring that your lashing will not shake out.

Tensioning
Prior to lashing off please tension the shroud or stay to the desired tension. Tensioning can be achieved in several ways:

1. The best method is to take your boat sailing and adjust the leeward shroud, letting the wind blow the rig to leeward and do the work for you. Tack back and forth in low to moderate winds and keep adjusting the leeward shrouds. Always keep the mast straight and in column. In the end, you want your leeward shrouds to just come loose at your wind reef point, usually about 15-20 knots of wind speed.

2. You can also bring a halyard down and tie it off to your lashing line and use a winch for tensioning. This method will probably mean that you would need to help the lashing line thru all the holes in the line terminators and distributors while at the same time adding tension with the winch. When you are tensioned up and ready, use the following directions to tie off your lashing very securely

Lashing Off
Please note the lashing is started at approximately 1/3 or less of the total lashing distance up from the bottom. This is critical as the knot will not slide down the lashing system due to the hourglass configuration. There are side forces tending to hold the knot up. If this is too high the knot will slide down and your shroud or stay will loosen.

For more great information go to Colligomarine.com

Monohull vs Multihull?

Monohull or Multihull?.png

We get these questions all the time: Are catamarans and trimarans really superior to monohulls? In what ways? Does it matter to me? What are the key differences between catamarans and trimarans? 

Level Sailing 
The most noticeable thing about sailing a catamaran or trimaran vs a traditional monohull is the lack of heeling. Stability is a big plus for families with young children or seniors who are not particularly steady on their feet. Because the boat is not as susceptible to the effects of wave action and does not heal the way a monohull does, it is much easier to walk around on deck and within the interior of the yacht while underway.

Even when powered up, a cat or tri will rarely heel more than 5-10 degrees before it’s time to reef. Gone are the days of bracing yourself in the cockpit, and living your life underway at 20+ degrees of angle. It’s a much more relaxing and convenient way to sail. No question about that.

Anyone who may be prone to seasickness will feel the effects of motion much less aboard a cat than they might on a mono. And the added stability on a cat makes the cook's job a lot less challenging both while underway and at anchor. Catamarans don't rock and roll the way monohulls do.

Speed—Sailing Performance

Cruising catamarans will typically be 25-30% faster than a cruising monohull of the same length! You basically get near racing monohull speeds, but with all the creature comforts that come with a cat. Trimarans are an entirely different deal, as they trend more toward the performance end of the spectrum, and can regularly double the sailing speed of monohulls on nearly any point of sail. Keep in mind that catamarans and trimarans are, however, much more sensitive to loading. The performance will suffer more on a cat that is loaded for cruising than on a comparable monohull. Keeping the boat light can be difficult, but is critical if fast passages are your goal. Take note…A clumsy tack on a cat that brings the boat into irons can be disastrous! Getting a cat moving from a dead stop (or worse - sailing backwards) can be quite difficult. They just don't recover as quickly as a monohull. If close to shore or another yacht, a cat in irons could spell disaster. So, the argument could be made that the skill set required for catamaran sailing needs to be somewhat more advanced.

Reefing

Sailing catamarans and, to a lesser extent, trimarans too, require vigilance when it comes to reefing. Since they don’t heel much, almost all additional wind force is converted to load on the rig. That’s where the speed comes from. But since the pressure on the sails quadruples as the wind speed doubles, crews must keep an eye on the weather and reef in good time to keep the boat safe and sailing flat. In fact, a properly reefed cat or tri will sail faster too, in freshening breezes. All manufacturers supply written guidelines denoting apparent wind speeds that require additional reefing.

Safety – Unsinkability

There are many aspects to safety where catamarans and trimarans shine. Often overlooked is the safety margin introduced with level sailing (see above). It is much easier to keep the crew aboard in rough weather when the boat stays level and is pitching less. Large cockpit spaces keep the crew well away from the lifelines as well. The speed of a multihull is another safety factor, as with decent weather information, it’s relatively easy to sail around severe weather systems before they can bear down on you. Should something go horribly awry, and the boat gets flipped (VERY rare), the lack of ballast, and additional positive flotation, means that nearly every catamaran and trimaran produced in the last few decades will remain on the surface of the water, right side up or not, until a rescue can be made. Nearly all cruising cats and tris have a substantial amount of reserve buoyancy, in the form of closed-cell foam, stashed in the nooks and crannies of the boat. Because of this, most could literally be cut into pieces and all pieces would still float. This makes fire your biggest safety concern aboard a cat. And the anchor windlass, but that’s a story for another day.

Motoring Performance/Maneuverability

Cruising catamarans and trimarans, with their easily driven hull forms and lightweight, enjoy excellent fuel efficiency when compared to monohulls, and track very straight. Cats almost always have twin engines, set many feet apart, which allow for tremendous control in tight situations. In fact, the boat can be spun in place or crabbed sideways without any way on. Try that on a monohull. Prop walk is minimal or nonexistent as well, and the redundancy of a second engine is appreciated should a mechanical issue arise underway. Nearly all trimarans have just one engine, so the differences there are slight.

Shallow Draft/Beachability

Because multihulls’ stability comes from the beam and extra hulls (form stability), there is no need for ballast or a substantial keel. This reduces overall weight and, importantly, draft as well. It is common for a 40+ foot cruising cat to have a draft less than 4 feet, allowing sailors to explore shallow areas monohullers fear to tread. Belize, the Bahamas, the Great Barrier Reef? No problem. Gunkholing around Mexico or the Chesapeake is easier too. If you have some quick underwater maintenance to do (replace prop shaft seals, zincs, a through-hull), most cats can be dried out at low tide on a flat area of sand or solid ground, resting happily on her stubby little keels. You can also nose right up to that perfect beach if the weather allows. Trimarans typically have no keels at all, and instead rely on a centerboard to prevent leeway, making them perfect for beaching (boom tent camping, anyone?).

More Living Space on a Catamaran

No doubt you’ve already realized the enormous gains in living space afforded by modern cruising cats. Typically a cat will have space below equivalent to a monohull 10+ feet larger. When combined with added cockpit space, possibly a flybridge, and more than doubling the deck space, it becomes a whole different ball game. It’s important to note that you not only gain a tremendous amount of space, but nearly all of that space if very livable and comfortable, whether at anchor or underway.

Seawind 1160 Lite Interior

Seawind 1160 Lite Interior

However, trimarans don’t show an increase in interior volume, and in fact, they tend to be smaller below than monohulls of the same size.

Let us know if we can offer any more information between a monohull, trimaran, or catamaran.


Learn more at 180marine.com

180 Marine is a distributor...serving performance-minded sailors, as a authorized Corsair Trimaran dealership. We're most active in the Western United States, Mexico, and Canada. 180 Marine strives to make sailboat ownership more exciting and enjoyable, as we expand our vital community of sailors who love adventure and sailboat racing.

What do Corsair trimarans do best?

Proud new owner of a Corsair 760

Proud new owner of a Corsair 760

They are fast.
They are safe.
They are exciting.
They are trailerable.
Versatile, fun and stable.
They deliver speed on a puff of wind.
Their shallow drafts allow you to coast directly up onto any beach.
There’s lots of room for the family and crew on the large trampolines.
The wide beams provide a flat stable platform under sail.
It’s quick and easy from trailer to sailing.

We have another 760 ready to hit the road from Denver Colorado, to Dana Point, California!
This 24-foot trailerable trimaran is easy to fold and compact when towing. Rig, launch and unfold in about 45  minutes, this model is simple, stress-free and can easily be managed alone!

Launching a Corsair 760

Launching a Corsair 760

New owners of a Corsair 760

New owners of a Corsair 760

Corsair 760.png

Hoku and Mandy, the new owners of this Corsair 760, are excited to bring their boat out to Southern California from Colorado! Hoku has been sailing it in Colorado where the summer and fall weather conditions have been perfect. Training with Richard Allen has been invaluable as Hoku gets to know the 760! And he's looking forward to joining in on a few local races to get a taste of competition.

Corsair 760.png
Corsair 760.png

Next, it's time to test the water's near Dana Point, California. This boat is perfect for a small family of 4 who is looking for adventure!

Corsair 760.png

Contact Richard Allen, CEO of 180 Marine for more information on all Corsair models. Contact >>

180 Marine serves performance-minded sailors every week, as a Corsair Trimaran dealership. We're most active in the Western United States, Mexico, and Canada. 180 Marine strives to make sailboat ownership more exciting and enjoyable, as we expand our vital community of sailors who love adventure and sailboat racing.

Richard Allen.png

11 steps to raising your mast on a Corsair trimaran

Corsair 760 Trimaran

Corsair 760 Trimaran

For all of you who are new to trimaran sailing, or for the avid Corsair Trimaran sailor who wants a brush-up, here is an awesome list of 11 steps on how to raise your mast on a Corsair Trimaran. You should print this out and keep it on your boat for reference!

MAST RAISING PROCEDURE

  1. Untie the mast from all supports.

Corsair trimaran.png

2. Attach cap shrouds and forestay or roller furling headstay to the mast.

3. Attach cap shrouds to the chainplates on the floats. If your boat has wire shrouds with Hifield levers take a bungee cord and hook one end to the upper toggle of the levers (the levers need to be in the open position. If you have an F-24 or early model Sprint with wire shrouds, go to the top of the turnbuckles), and the other to the daggerboard up and down lines on the deck so that the levers are held in a vertical position.

Corsair trimaran.png
Corsair trimaran.png
Corsair trimaran.png

4. Place the yoke onto the deck hinges and pin into place. The yoke should be facing the bow with its curved edge facing down so that it clears the halyard blocks on the mast step. Place the long ½” pin on the deck nearby so that you are ready to pin the mast into place. On 750s/760s attach the mast raising hinge to the deck and pull the long ½” pin out and lay on the deck nearby.

5. Carefully walk the mast back until it is even with the yoke or mast raising hinge. Watch the spreaders on the aft beams as you go back so as not to bang them. Once in position, lift the yoke up to the mast, and place the ½” pin through the mast base, and put the clips in the pin so it cannot fall out. Be careful moving the mast at this point as it will become stern heavy, and want to lift up.

6. Attach the mast raising wires to the pad eye on the mast, and to the anchor loops on the deck. If a roller furler is used, make sure it is above the wire. Insert the mast-raising pole into the yoke or into the mast and attach the mast raising wire to the pad eye on the mast. On the 31’s, as you lift the pole into position, it will get a little hard as the spreaders are lifted over the rollers on the aft mast support.

Corsair trimaran.png
Corsair trimaran.png

7. Unroll enough line from the trailer winch to reach the pole. Attach the jib and screacher halyards to the winch line, pull them tight until the connection between the halyards and the winch line is just forward of the V in the mast raising pole, and cleat it off on the cleat at the base of the mast  (In the case of the 24, 750 or 760 with clutches on the mast: secure the halyards in their clutches and back them up on horn cleats or tie around the mast or the rope clutch itself for security). Take a final look around for potential snags on the shrouds, and make sure all is clear.

8. If you raise the mast with the bowsprit in place, be aware that as the line wraps around the spool, it will not spool evenly, and can possibly jump off the spool if not caught soon enough. I recommend leaving the bowsprit out until the mast is up for this reason as well as the winch line will chafe a groove on the side of it. You are now ready to raise the mast.

Corsair 760.png

9. With one person at the winch, and one on deck by the mast base, begin cranking the winch. If the ground is not level, or there is a side wind, the mast will want to lean away from the center of the boat, so evaluate this possibility before getting too far and anticipate the direction it will want to go. The mast raising wires will prevent the mast from going too far, but it is best to be aware of this. The person on deck can help out here, by gently pulling on the correct mast wire. Continue raising the mast, the deck person is watching the shrouds to make sure there are no snags. If the mast starts to lean to one side a lot, or it gets suddenly hard to crank, STOP. Look around for something hanging up. Once the mast is part way up, NEVER WALK BENEATH THE MAST. If all is clear, continue to raise the mast until it rests on the mast step ball, and attach the forestay to the stem fitting. You can now release the trailer winch, and reattach it to the bow of the boat for launching. You can now remove the pole, yoke, and or mast raising hinge, and bungie cords from the levers if used.

Corsair 760.png

10. At this time, you can now string all the halyards through the mast base blocks and/or deck organizers and run them back to the cockpit and through the rope clutches if applicable, and attach the boom. Launch the boat, unfold the floats, tension the shroud levers if applicable, and remove the mast raising wires.

Corsair 760.png

11. To lower the mast, just reverse this procedure in the exact order written.
The bungee cords are not needed for lowering the mast.

Always make safety the first priority in both raising, and lowering the mast. Neither process is very difficult. With some practice, it will become an easy thing to do. If at any time, any of the mast raising gear gets damaged, repair or replace it before doing another stepping of the mast, as it may have become too weak to perform its job safely. Always check and maintain all parts of your boat for the best performance possible.

HAPPY TRIMARAN SAILING!

Thank you Don Wigston with Windcraft for documenting this process!


Reach out if you have a specific question about Corsair trimarans,
we're happy to help.

Other helpful resources

Corsair 760 >>
Corsair 760 Sport >>
Corsair 760R >>
Corsair Sailing Manual >>

180 Marine is a distributor...serving performance-minded sailors, as a Corsair Trimaran dealership. We're most active in the Western United States, Mexico, and Canada. 180 Marine strives to make sailboat ownership more exciting and enjoyable, as we expand our vital community of sailors who love adventure and sailboat racing.

Contact Richard Allen for the latest news on the Corsair 760 richard@180marine.com

180 Marine is the fastest growing Corsair Marine Dealer in the U.S., owned and operated by Richard Allen and Leslie Gabriel, long time Corsair trimaran racers, day sailors and cruisers.

180 Marine is the fastest growing Corsair Marine Dealer in the U.S., owned and operated by Richard Allen and Leslie Gabriel, long time Corsair trimaran racers, day sailors and cruisers.

Why would I ever consider a trimaran?

Corsair Cruze 970

Corsair Cruze 970

Thank you, John Rich, for sharing these great trimaran insights!

As a multihull man, in particular, one who loves and sails trimarans, many people ask me...

“Why would I ever consider a trimaran?”

They often say: 

1. Trimarans have a smaller accommodation

Correct
The internal accommodation is compensated by the living space outside. After all, when you go sailing you do not want to spend your time inside your cabin, do you? You want to enjoy the environment and atmosphere. Most often we sail the trimarans in warm waters and to get the most out of the time onboard, to have fun with people around us, above all to enjoy our sailing experience. That is what the trimarans offer, in particular, our Corsair Trimarans! The photo above is a Corsair Cruze 970.

2. Trimarans take on board less “stuff”

Fantastic 
Contrary to many sailor’s inventories on board these vessels trimarans are not floating storage spaces. The old motto is “when you go sailing take only what you need and then take only stuff that is light”. In fact, next time you go sailing just spend the day taking stock of what you have onboard and weigh it all on the scale. You will be very surprised how much unnecessary stuff you carried in the past when you went sailing. Now sort out what is really required on board. Weigh what you selected and put it on board. Then weigh what you need on your trip, take “just in case” few extras. Now load your boat taking care of what is where so you can easily find it. You can make a little packing scratch so your crew could be informed where things are located and why. Often people sail with full tanks of fuel and water, why? 

3. Trimarans are wide

Excellent 
The wider the boat the better it is, meaning she will hill less and with a wider overall beam, the boat will be also stiffer. Flatter sailing platform on trimarans equates the faster speed. 

4. Trimarans need more space to park onshore, on the water or at the marina

Possibly
Generally, it's correct with trimarans exceeding 38 foot or 12 meters. With smaller trimarans such as a Corsair trimaran, there is a possibility of easy reduction of the beam by folding the floats tacking them neatly under the central hull. This operation is extremely easy and allows Corsair trimarans to be trailerable behind suitable SUVs, 4WDs and Pickup Tracks in case of Corsair 37. This gives the owners much-needed freedom of mobility to follow the summer season across a continent, or each time sail in different geographical location, or if the owner likes to race major regattas to take their boat there. Additionally, your Corsair can serve along the way as a comfortable and safe place to sleep. This makes Corsair almost equal the Airstream caravan (or another type) with one major difference and greatest asset. Your Corsair will float, it will sail and motor around the lake, river, bay and the sea. It will above all do this very fast giving you a big smile each time you go sailing.

As an owner of a Corsair trimaran, you have many ways to store your trimaran. You can do this folded on the trailer with the mast and rigging down on your property next to your house, or at the boat-yard on the hard-stand, alternatively on any property where you can legally park your Corsair trailer.

You can keep your Corsair on the trailer, folded with the mast/rig up. This way your trimaran is more economical to store near the water where she can be easily launched. 

Alternatively, when your marina or boat-yard has a dry storage area with mast/rig up and floats fully open you can keep your Corsair ready to deploy into the water and go sailing. 

While on the water at the marina you can moor your trimaran as is, space permitting, at the jetty or your pontoon. The best thing about Corsair folding ability is that while the marina space is at the premium you can fold your floats while motoring to your designated location and “park” your trimaran with her mast/rig up and just step off and on your boat going sailing at your leisure with a minimum of fuss. 

Lastly, you can moor your boat on a designated mooring and use a marina’s tender service or your own dinghy to get on and off your boat.

All these options give you great flexibility.

5. Trimarans can tip over

Sometimes
Every now and then we hear of horror stories of boats tipping over. When it happens to a monohull because of the ballast the boat most likely will right herself after a while. Onboard the catamarans or trimarans it is much harder. One thing is certain multihulls because they have no heavy ballast that will float on the surface mostly because of positive buoyancy due to construction materials used onboard. 

The most important thing is to understand why multihulls can tip over and always sail within the safety margins. On monohulls, we try to keep as much sail area up to go faster, while on multihulls it is paramount to reef as early as possible anticipating changing nature of the weather fronts and local weather conditions. In fact, the multihull with less sail area or center of sail gravity will sail often faster and positively safer. The biggest challenge comes when sailing multihulls in the heavy weather, which is the art form in itself and demands practice and experience. In these situations, if you must continue your passage you will make it with utter respect and caution giving the most attention to the position of your trimaran in relation to the waves.

In all this please remember, your trimaran will be very fast and its safety will be governed by the ability to get to your destination before the weather gets foul.

Corsair 760

Corsair 760

6. Trimarans are more expensive

Yes
Buying a trimaran is like buying a sports car. You can buy a car that will get you from A to B, you can also buy SVU, Pickup, Van, Station Wagon, etc. You can also buy a Prestige or Exotic car. The function of each will be exactly the same, yet the price will vary between $10,000 and $1,000,000. That is 100 times difference in price. In other words, you pay for what you want based on your needs, desires, and status. 

Trimarans are the most sophisticated types of boats on the market. That is why you do not see them very often and when you see one sailing you know that it is an ultimate sailing machine which will give you prestige, comfort within the confines of its platform and above all excellent performance. 

Ultimately the choice of boat one chooses will be up to the owner, we can only guide you towards your decision based on your sailing plans.

Learn more about the Corsair 760 HERE >>

ABOUT JOHN RICH
John Rich is an outstanding yachtsman and multihull sailor and composite boat builder as well as an extraordinary man with a wealth of knowledge and unrivaled life experience which makes him a highly sought professional businessman, salesman, and trainer. He is an Australian sales representative for Corsair Trimarans and works as a salesman with Multihull Central, dealer of Corsair Trimarans and Seawind Catamarans.